SN75DP130 EVM User s Manual

Transcription

1 SLLU October 00 - Revised January 0 SN7P0 EVM User s Manual High Performance nalog / Interface Group STRT The SN7P0 is a single port ual-mode isplayport (P++) repeater that regenerates the P high speed digital link. The device complies with the VES Embedded isplayport Standard Version. supporting up to four lanes of. Gbps (HR) and P++ dual-mode TMS signaling for full HMI.a data rate support. The device compensates for P related frequency loss and switching related loss to provide the optimum P electrical performance from source to sink. The Main Link signal inputs feature configurable equalizers with selectable boost settings. t the Main Link output, four primary levels of differential output voltage swing (V O ) and four primary levels of pre-emphasis are available, as well as a secondary level of boost adjustment, programmed through I, for fine-tuning the Main Link output. The device can monitor the UX channel and automatically adjust the output signaling levels and input equalizers in response to Link Training commands. dditionally, the SN7P0 output signal conditioning and EQ parameters are fully programmable through the I interface. The SN7P0 offers separate UX and source ports and an UX sink port. This minimizes component count when implemented with a graphics processor (GPU) comprising separate and UX interfaces. For GPUs with combined /UX, the device can operate as a FET switch to short circuit the UX channel coupling caps while connected to a TMS sink device. Other sideband circuits such as Hot Plug etect (HP) are optimized to reduce external components, providing a seamless connection to Intel, M, and NVII graphics processors. The SN7P0 is optimized for mobile applications, and contains activity detection circuitry on the Main Link input that transitions to a low-power Output isable mode in the absence of a valid input signal. Other low power modes are supported, including a Standby mode with typical dissipation of ~mw when no video sink (eg. monitor) is connected. The device is characterized for an extended operational temperature range from 0º to 8º. SN7P0 EVM January 0

2 ontents Introduction... SN7P0 Evaluation Module onfiguration... SN7P0 EVM Kit ontents... escription of EVM oard... P onstruction...6 SN7P0 EVM oard Layout...6 SN7P0 EVM oard onstruction...9 SN7P0 EVM Material Listing...0 SN7P0 EVM oard Schematics...0 ppendix ill of Materials... Figures Figure. SN7P0 EVM lock iagram... Figure. SN7P0 EVM Switch and Jumper Location (Top)... Figure. SN7P0 EVM Switch and Jumper Location (otom)... Figure. SN7P0 EVM Top Layer...6 Figure. SN7P0 EVM Ground Layer...7 Figure 6. SN7P0 EVM Power Layer...7 Figure 7. SN7P0 EVM Power Layer...8 Figure 8. SN7P0 EVM Ground Layer...8 Figure 9. SN7P0 EVM ottom Layer 6 (Mirrored)...9 Figure 0. EVM Layer Stack-up...9 Tables Table. Jumper and Switch Functionality... Table. P0 EVM ill of Materials... SN7P0 EVM January 0

3 Introduction The SN7P0 is a high-speed one-to-one redriver for isplay Port signals. This guide describes the construction and usage of the EVM for the SN7P0. The EVM is meant to serve as an evaluation tool for the SN7P0, as well as a reference design for the device. SN7P0 Evaluation Module onfiguration SN7P0 EVM Kit ontents This EVM kit should contain the following items: SN7P0 EVM board Power Supply This user s manual escription of EVM oard The SN7P0 EVM is designed to provide easy evaluation of the SN7P0 device. It is also meant to serve as a reference design to show a practical example of how to use the device in a mass-production system. Power onversion.v Regulated/.0V GPU/ P++ Source P SN7P0 P isplayport Enabled Monitor or HTV LP_ Enable Figure. EVM SN7P0 EVM lock iagram SN7P0 EVM January 0

4 P Out JMP SW P In f Figure. SN7P0 EVM Switch and Jumper Location (Top) Figure. SN7P0 EVM Switch and Jumper Location (otom) SN7P0 EVM January 0

5 JMP JMP JMP (not installed) JMP7 (not installed) JMP8 (not installed) s Jumper Number/ Switch JMP JMP9 JMP0 JMP JMP JMP SW SW SW Functionality Sink Over Ride ( the pin input from the sink is independently pulled high by a k pullup to allow the P0 EVM to be in TMS mode independent of the sink ) HP Sink Over Ride ( the HP pin input from the sink is independently pulled high by a k pullup to allow the P0 EVM to provide an indication of the sink presence) llows for the three settings of either Equalization (in GPIO ux channel pullup voltage ( or.v) llows for easy connect to the V rail for monitoring llows for easy connect to the.v rail for monitoring llows for selection of EVM power from the wall or 9V battery Normal position would be "Wall" to "VIN" HP Override for port (Only used to override or create an HP) HP Override for port (Only used to override or create an HP) Override for port (Only used to change from 0 to ) Override for port (Only used to change from 0 to ) Priority ontrol (P Out /) Low Power mode control (LP/Normal) Vdd* Voltage selection (Some EVM's will have this voltage fixed) Selection Normal operation = JMP:- Over ride = JMP:- Normal HP operation = JMP:- Over ride HP = JMP:- Table. Jumper and Switch Functionality The power supply provided with this EVM is a +V power supply. ny ac-to-dc converter can be used as long as it has a.mm plug with the positive terminal in the center. The output voltage of the power supply should be within the range of +.V to +0V (JMP9 = VIN_WLL). For portability, a battery holder is also provided for use with a 9V battery (JMP9 = TT_IN). SN7P0 EVM January 0

6 P onstruction This section discusses the construction of the EVM boards. It includes the board schematics and Gerber files to show how the board was built. SN7P0 EVM oard Layout This EVM was designed to show the implementation of this device on a 6-layer board. The pin assignments of the input ports of the SN7P0 device are optimized for the P mount P connector. This allows easy routing of the input traces without the need for vias. The output port of the SN7P0 device is optimized for a direct connection to a TMS receiver. On this EVM the output port is routed to a P connector. In this case the pin assignment for the connector is exactly opposite of the device. Every effort was made to keep the routing as clean as possible to the P connectors. The board was designed to maintain 00 differential impedance between each of the TMS differential traces. For the material used in this design (FR Turbolad 70), and with the stackup (shown below) this required the differential traces to be mil wide with an mil air gap between differential pairs. minimum spacing of times the trace width was maintained to all other components to prevent coupling. Figure. SN7P0 EVM Top Layer 6 SN7P0 EVM January 0

7 Figure. SN7P0 EVM Ground Layer Figure 6. SN7P0 EVM Power Layer 7 SN7P0 EVM January 0

8 Figure 7. SN7P0 EVM Power Layer Figure 8. SN7P0 EVM Ground Layer 8 SN7P0 EVM January 0

9 Figure 9. SN7P0 EVM ottom Layer 6 (Mirrored) SN7P0 EVM oard onstruction The EVM board is a 6-layer board constructed of FR Turbolad 70 material. The board stackup consists of a signal layer on top, a ground layer, a power layer, power, ground, and a Signal layer on bottom. Signal Ground V V Ground Figure 0. EVM Layer Stack-up Signal 9 SN7P0 EVM January 0

10 SN7P0 EVM Material Listing The complete ill of Material for the EVM is listed in ppendix. SN7P0 EVM oard Schematics The board schematic sheets for the EVM are shown at the end of this document. 0 SN7P0 EVM January 0

11 ppendix ill of Materials The following table is the complete OM for the EVM. Item Quantity Reference Value 6,,,,,6,7,8,0,,,,,,6,7 0.uF 9,8 0.0uF 9,, 0.uf 0, 0u NI 6 u 7,7 0.0u 8 0u u 0 6 8,9,,,6,7 0.0uF 0,.0uf, LE 0V JMP,JMP,JMP,JMP6,JMP7 Header x JMP,JMP,JMP8 Header x 6 JMP9 Header x NI 7 JMP0 NI 8 J isplay_port_onnector_sink 9 J isplay_port_onnector_source 0 J attery Holder 9V L HI06N0R-00 P RP7 R,R9 M 7 R,R,R6,R7,R,R,R 00k_NI R,R 0_NI 6 R 7k_NI 7 R8 M_NI 8 R0,R M_NI 9 R,R,R9,R0.7k 0 R6 M R7 0 R8 00k R 0 R.k R,R6 0k 6 R7 NI 7 R8 6.9k 8 R9 k 9 U SN7P0 0 U REG0-. Table. P0 EVM ill of Materials SN7P0 EVM January 0

12 EVLUTION OR/KIT/MOULE (EVM) ITIONL TERMS Texas Instruments (TI) provides the enclosed Evaluation oard/kit/module (EVM) under the following conditions: The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods. Should this evaluation board/kit not meet the specifications indicated in the User s Guide, the board/ kit may be returned within 0 days from the date of delivery for a full refund. THE FOREGOING LIMITE WRRNTY IS THE EXLUSIVE WRRNTY ME Y SELLER TO UYER N IS IN LIEU OF LL OTHER WRRNTIES, EXPRESSE, IMPLIE, OR STTUTORY, INLUING NY WRRNTY OF MERHNTILITY OR FITNESS FOR NY PRTIULR PURPOSE. EXEPT TO THE EXTENT OF THE INEMNITY SET FORTH OVE, NEITHER PRTY SHLL E LILE TO THE OTHER FOR NY INIRET, SPEIL, INIENTL, OR ONSEQUENTIL MGES. Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit or contact TI. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Mailing ddress: Texas Instruments Post Office ox 60 allas, Texas 76 opyright 0, Texas Instruments Incorporated REGULTORY OMPLINE INFORMTION s noted in the EVM User s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal ommunications ommission (F) and Industry anada (I) rules. For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING EVELOPMENT, EMONSTRTION OR EVLUTION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part of F or IES-00 rules, which are designed to provide reasonable protection against radio frequency interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference. General Statement for EVMs including a radio User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and power limits. ny use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is the user s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations. ny exceptions to this is strictly prohibited and unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its acceptable authorization.

13 For EVMs annotated as F FEERL OMMUNITIONS OMMISSION Part ompliant aution This device complies with part of the F Rules. Operation is subject to the following two conditions: () This device may not cause harmful interference, and () this device must accept any interference received, including interference that may cause undesired operation. hanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. F Interference Statement for lass EVM devices This equipment has been tested and found to comply with the limits for a lass digital device, pursuant to part of the F Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. F Interference Statement for lass EVM devices This equipment has been tested and found to comply with the limits for a lass digital device, pursuant to part of the F Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. onnect the equipment into an outlet on a circuit different from that to which the receiver is connected. onsult the dealer or an experienced radio/tv technician for help.

14 For EVMs annotated as I INUSTRY N ompliant This lass or digital apparatus complies with anadian IES-00. hanges or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. oncerning EVMs including radio transmitters This device complies with Industry anada licence-exempt RSS standard(s). Operation is subject to the following two conditions: () this device may not cause interference, and () this device must accept any interference, including interference that may cause undesired operation of the device. oncerning EVMs including detachable antennas Under Industry anada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry anada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry anada to operate with the antenna types listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated. ntenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. ~ et appareil numérique de la classe ou est conforme à la norme NM-00 du anada. Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l autorité de l'utilisateur pour actionner l'équipement. oncernant les EVMs avec appareils radio Le présent appareil est conforme aux NR d'industrie anada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : () l'appareil ne doit pas produire de brouillage, et () l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. oncernant les EVMs avec antennes détachables onformément à la réglementation d'industrie anada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie anada. ans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent émetteur radio a été approuvé par Industrie anada pour fonctionner avec les types d'antenne énumérés dans le manuel d usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.

15 Important Notice for Users of this Product in Japan This development kit is NOT certified as onfirming to Technical Regulations of Radio Law of Japan! If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product: () Use this product in a shielded room or any other test facility as defined in the notification #7 issued by Ministry of Internal ffairs and ommunications on March 8, 006, based on Sub-section. of rticle 6 of the Ministry s Rule for Enforcement of Radio Law of Japan, () Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this product, or () Use of this product only after you obtained the Technical Regulations onformity ertification as provided in Radio Law of Japan with respect to this product. lso, please do not transfer this product, unless you give the same notice above to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan. Texas Instruments Japan Limited (address) -, Nishi-Shinjuku 6 chome, Shinjukku-ku, Tokyo, Japan ご使用にあたっての注意 本開発キットは技術基準適合証明を受けておりません 本製品のご使用に際しては 電波法遵守のため 以下のいずれかの措置を取っていただく必要がありますのでご注意ください () 電波法施行規則第 6 条第 項第 号に基づく平成 8 年 月 8 日総務省告示第 7 号で定められた電波暗室等の試験設備でご使用いただく () 実験局の免許を取得後ご使用いただく () 技術基準適合証明を取得後ご使用いただく なお 本製品は 上記の ご使用にあたっての注意 を譲渡先 移転先に通知しない限り 譲渡 移転できないものとします 上記を遵守頂けない場合は 電波法の罰則が適用される可能性があることをご留意ください 日本テキサス インスツルメンツ株式会社東京都新宿区西新宿 6 丁目 番 号西新宿三井ビル

16 EVLUTION OR/KIT/MOULE (EVM) WRNINGS, RESTRITIONS N ISLIMERS For Feasibility Evaluation Only, in Laboratory/evelopment Environments. Unless otherwise indicated, this EVM is not a finished electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end product. Your Sole Responsibility and Risk. You acknowledge, represent and agree that:. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and rug dministration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees, affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates, contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard.. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to perform as described or expected.. You will take care of proper disposal and recycling of the EVM s electronic components and packing materials. ertain Instructions. It is important to operate this EVM within TI s recommended specifications and environmental considerations per the user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including input power and intended loads. ny loads applied outside of the specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. uring normal operation, some circuit components may have case temperatures greater than 60 o as long as the input and output are maintained at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please be aware that these devices may be very warm to the touch. s with all electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development environments should use these EVMs. greement to efend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "laims") arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether laims arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected. Safety-ritical or Life-ritical pplications. If you intend to evaluate the components for possible use in safety critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices which are classified as F lass III or similar classification, then you must specifically notify TI of such intent and enter into a separate ssurance and Indemnity greement.

17 NOTES:. SILKSREEN LL JUMPERS N HEERS.. PLE LL PRTS ON 0 OR 90 EGREE ORIENTTION.. HIGH SPEE SERIL T SHOUL E ROUTE S SINGLE-ENE 0 OHM TRNSMISSION LINES. ROUTING ISTNE SHOUL E INHES OR LESS.. USE FR-70 MTERIL.. PLE TI LOGO IN TOP SIE METL ER REVISIONS ER NUMER TE /--/-- Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products and publications or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. ll products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. ustomers are responsible for their applications using TI components. In order to minimize risks associated with applications using TI components, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. The information in this document is provided by TI as a courtesy and in no way constitutes a reference design. ny direct duplication of this design in its entirety is strictly prohibited without expressed written approval by TI. Furthermore, TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI s publication or information regarding any third party s products or services does not constitute TI s approval, warranty or endorsement thereof. opyright 009. Texas Instruments Incorporated P0 T SHEET REVISION: 0.98 T SHEET LST UPTE ON: 0/0/0 ENGINEER K SHW LYOUT Steve Gregory RELESE TE 0/08/0 TE 0/09/0 TE TEXS INSTRUMENTS SHEMTI TITLE PGE TITLE P0 EVM SIZE OUMENT NUMER REV SHEET 6696 of 8

18 R M SGN J GN7 ML_n GN8 GN GN9 ML_p GN0 ML_n GN ML_p 6 ML_n 7 GN 8 8 ML_p 9.0uF ML_0n 0 GN ML_0p (GN) P_E (GN) UX_p (SL) GN6 6 UX_n (S) 7 HP 8 P_PWR_RTN 9 P_PWR 0 isplay_port_onnector_sink_0 R PV P_PWR_SINK 0 (NI) P Power does not normall get connected in the P cable PV MIN_LINK_IN_N MIN_LINK_IN_P MIN_LINK_IN_N MIN_LINK_IN_P MIN_LINK_IN_N MIN_LINK_IN_P MIN_LINK_IN_0N MIN_LINK_IN_0P E UX_P_SL_IN UX_N_S_IN 7 0.uF 0.uF 0.uF 6 0.uF 9 0.uF 0.uF 0.uF 0.uF R 00k (NI) R 00k (NI) MIN_LINK_N MIN_LINK_P MIN_LINK_N MIN_LINK_P MIN_LINK_N MIN_LINK_P MIN_LINK_0N MIN_LINK_0P R6 0 R 0 SL_SOURE S_SOURE P SINK_OUTPUT P_HP_SINK_OUTPUT 0 0.uF R7 K (NI) PV R8 K (NI) 0.uF UXSL_SOURE_P UXS_SOURE_N U INn INp INn INp INn INp IN0n IN0p _SR (Out) HP_SR (Out) UX_SRp UX_SRn V Rddc SL_ S_ R and R6 can be installed when is high allowing SL/S to be routed to the input of the P0 R9 7K (NI) P0 see Page E R0 M NI PGE TITLE P0 SOURE ONNETION TEXS INSTRUMENTS SIZE OUMENT NUMER 6696 REV PGE of 8

19 U OUT0p OUT0n OUTp OUTn OUTp OUTn OUTp OUTn _SINK (In) P0_P P0_N 0 P_P 9 P_N 7 P_P 6 P_N P_P P_N JMP R TMS OVERIE 0 SILKSREEN OVR Pin erg Jumper R _OVR M NORM K PV uF 0.uF 0.uF 7 0.uF 9 0.uF 0.uF 0.uF 0.uF PV R 00K P_OUTPUT_0_P P_OUTPUT_0_N P_OUTPUT P P_OUTPUT N P_OUTPUT P P_OUTPUT N P_OUTPUT P P_OUTPUT N _SINK J ML_0p GN ML_0n ML_p GN ML_n ML_p GN ML_n ML_p GN ML_n GN7 GN8 GN9 GN0 SGN 0.0uF R M UX_SNKp UX_SNKn 8 7 UX_SINK_P UX_SINK_N R 0 R6 0 UX_SINK_OUTPUT_P UX_SINK_OUTPUT_N 6 7 GN UX_p GN6 UX_n SILKSREEN OVR HP_OVR NORM NOTE: HP OVERRIE SHORT -> FOR NORML HP SHORT -> FOR FORE HP (HIGH) R7 00K HP_SINK (IN) P0 HP JMP Pin erg Jumper HP_OVERIE R9 00K R8 K PV HP_SINK 8 HP 9 RTN 0 P_PWR isplay_port_onnector_source PV see Page E R0 0 (NI) R0 can be installed to provide P source power for dongle support PGE TITLE P0 SOURE ONNETION TEXS INSTRUMENTS SIZE OUMENT NUMER 6696 REV PGE of 8

20 PV see Page7 S_SMT see Page7 SL_SMLK R.6K R.6K U R_EQ_MI SILKSREEN R_EQ_PU R_EQ R_EQ_P R_EQ_MI JMP R_EQ_PU R_EQ_P R_EQ R Pin-T erg Jumper R.6K R.6K R 0 (NI) R6 0 (NI) PV PV I PULLUP I HEER PWR SILKSREEN GN SILKSREEN EN_PU EN_MI EN EN_P R7.6K EN_MI JMP EN_PU EN_P R8.6K EN_EQ 6 V Ren = 00k EN J x Keyed onnector I_PWR R K PV JMP LOL_I_PULLUP R K Pin-T erg Jumper LOL_SL R9.6K Pin-T erg Jumper R0.6K SL_TL LOL_S S_TL V_REG_PIN SILKSREEN ENLE RST_N JMP6 Pin erg Jumper R.99K RSTN R.99K (NI) NOTE: RSTN is a.0v circuit. o not drive this input more than the spec of.v V.0V 0k RSTN P0 0. uf PGE TITLE P0 ONTROL TEXS INSTRUMENTS SIZE OUMENT NUMER 6696 REV PGE of 8

21 PV PV R6 0 SEE INSTLL/NI NOTE V_SS_V_S P0V R 0 NI SEE INSTLL/NI NOTE 6 6 V0_SS_N_S V_SS_N_S V_SS_V0_S V_SS_V_S V_SS_V_S V_SS_V_S U N0_SS_V_S N_SS_V_S N_SS_V6_S 7 N_SS_V7_S P0V R7 0 NI SEE INSTLL/NI NOTE V_P0V 0.00uF 0.00uF 0.00uF 0.00uF 6 0.0uF 7 0.0uF 8 0.uF 9 0.uF 0 0.uF 0.0uF 0.0uF 0.00uF PLE NER THE P0 EVIE. 0.00uF 0.00uF uF PLE NER THE P0 EVIE. PV V_REG R9 0 SEE INSTLL/NI NOTE P0V R0 0 NI SEE INSTLL/NI NOTE V_REG_PIN V_REG_PIN V_REG_SS_V8_S P0 N 7 N 0 N 6 GN 8 GN GN THERML_P 9 6 U R8 k /REG_LE_PU YELLOW E 7 uf PLE NER THE P0 EVIE. 8 0.uF 9 0.0uF uF INSTLL/NI NOTE for P0 SS/S devices P0-SS: INSTLL 0 ohm R6, R9 NI R, R0, R7 R 6.9K REG_LE_SE E ZXT09N0E6 /REG_LE P0-S: INSTLL 0 ohm R, R0, R7 NI R6, R9 P0V PV uf uf 0.uF 0.uF 0.0uF 6 0.0uF 7 uf 8 uf 9 0.uF 0 0.uF 0.0uF 0.0uF LOL EOUPLING PITORS. PLE NER THE P0 EVIE. TEXS INSTRUMENTS PGE TITLE P0 POWER SIZE OUMENT NUMER REV PGE 6696 of 8

22 PV P0V uf R.99K 6 7 U IN OUT IS EN F SS GN TPS70 R.9k % 68uf + P0V_REG 0uf + 6.0uf L HI06N0R uF P0V 8 0.uF 9 0.0uF JMP7 NI R 00 GREEN uF SILKSREEN.0V_HIGH.0V_NOM R9.k % R.6k % JMP8 P0V_NOM P0V_HIGH P0V_LOW R6.9k % R7 9k % R8.87k % NOTE: PLE ULK EOUPLING PITORS NER THE REGULTORS N FERRITE ES..0V_LOW NOTE: REMOVE R IF JMP8 IS INSTLLE. PV 9V PV_REG 6 0uF PV 6 0.uF R0 7 GREEN NI 6 U Vin Vout GN GN NR/djust Enable REG0-67 uf 6 0uF 6 uf 6 0uF L HI06N0R uF JMP9 NI SILKSREEN PV_HIGH PV_LOW PV_NOM R6 K R.K JMP0 NI R 0K PV_NOM PV_HIGH PV_LOW R 0K R NI R 6.9K NOTE: REMOVE R IF JMP0 IS INSTLLE. NOTE: PLE ULK EOUPLING PITORS NER THE REGULTORS N FERRITE ES. J + 9V - attery Holder 9V 9V_TT_IN P SLEEVE TIP SHUNT RP7 SILK = +9V GN 9V_WLL_IN SILKSREEN TT 9V WLL 0V, JMP Pin-T erg Jumper 9V IN 9V 68 0uF 69 uf PGE TITLE EXT POWER INTERFE TEXS INSTRUMENTS SIZE OUMENT NUMER 6696 REV PGE 6 of 8

23 TK TMS PWRON0Z_TEN0 SMUS SMUSZ I HS TEN SS FULLPWRMGMTZ_SM TI HS_SUSPEN TO TRSTZ TIS SL_SMLK S_SMT U_VUS SS_SUSPEN PV PV PV_ P0V_ P0V_ PV_OS PV_ PV US_P_UP see Page8 US_M_UP see Page8 US_SSRXP_UP see Page8 US_SSRXM_UP see Page8 US_SSTXP_UP see Page8 US_SSTXM_UP see Page8 SL_SMLK see Page S_SMT see Page US_VUS_UP see Page8 REV PGE OUMENT NUMER SIZE of TEXS INSTRUMENTS PGE TITLE 6696 US I REV PGE OUMENT NUMER SIZE of TEXS INSTRUMENTS PGE TITLE 6696 US I REV PGE OUMENT NUMER SIZE of TEXS INSTRUMENTS PGE TITLE 6696 US I JTG is for lab evaluation only. The customer can leave these pins unconnected. US_P_N US_P_N0 US_M_N0 US_SSRXP_N0 US_SSRXM_N0 US_SSTXP_N0 US_SSTXM_N0 US_P_N US_M_N US_SSRXP_N US_SSRXM_N US_SSTXP_N US_SSTXM_N US_M_N US_SSRXP_N US_SSRXM_N US_SSTXP_N US_SSTXM_N US_P_N US_M_N US_SSRXP_N US_SSRXM_N US_SSTXP_N US_SSTXM_N OVERUR0Z ENLE PWR_MGMT SILKSREEN I SMUSZ ENLE TEN SMUS ISLE ISLE R67 0 r00 R67 0 r00 SW Light Touch Switch SW Light Touch Switch R7.7K r00 R7.7K r00 7 uf 7 uf 7 GREEN 7 GREEN U TUS800 PFP_s-pqfp-g80 U TUS800 PFP_s-pqfp-g80 US_P_N0 US_M_N0 V V US_SSRXP_N0 6 US_SSRXM_N0 7 US_SSTXP_N0 8 US_SSTXM_N0 9 V 0 V US_SSRXP_N US_SSRXM_N US_SSTXP_N US_SSTXM_N V 6 US_P_N 7 US_M_N 8 V 9 V 0 HS SS HS_SUSPEN SS_SUSPEN V JTG_TK 7 JTG_TMS 8 JTG_TO 9 JTG_TRSTZ 0 JTG_TI FULLPWRMGMTZ_SM V GRSTz SL_SMLK S_SMT SMUSZ 6 V 6 PWRON0Z_TEN0 9 OVERUR0Z 0 V 8 V 7 V V US_M_N US_P_N V 6 US_SSRXP_N 7 US_SSRXM_N 8 US_SSTXP_N 9 US_SSTXM_N 0 V V US_SSRXP_N US_SSRXM_N US_SSTXP_N US_SSTXM_N 6 V 7 V 8 US_M_N 9 US_P_N 60 V 6 V 6 US_SSTXM_UP 6 US_SSTXP_UP 6 US_SSRXM_UP 6 US_SSRXP_UP 66 V 67 V 68 US_M_UP 69 US_P_UP 70 V 7 VR 7 US_VUS 7 XO 7 VSS_OS 7 XI 76 V_OS 77 US_R 78 USR_RTN 79 V 80 V P 8 R7 (NI) R7 (NI) R60.7K r00 R60.7K r00 R9 0K r00 % R9 0K r00 % JP JP R6 0K r00 R6 0K r00 JP NI_onn x shroud JP NI_onn x shroud Y ES-MHZ Y ES-MHZ R8 90.9K r00 % R8 90.9K r00 % R6 0K r00 % R6 0K r00 % R76 k R76 k 6 GREEN 6 GREEN R7 M R7 M R70 (NI) R70 (NI) U6 TPS809K U6 TPS809K V GN RESETZ R7.7K r00 R7.7K r pF 70 8pF GREEN GREEN JP JP R66 0 r00 R66 0 r00 7 8pF 7 8pF 8 GREEN 8 GREEN JP JP R6.7K r00 R6.7K r00 R69 (NI) R69 (NI) R6 0 r00 R6 0 r00 R7.7K r00 R7.7K r00 R6.7K r00 R6.7K r00 R68 0 r00 R68 0 r00 R7 (NI) R7 (NI)

24 J6 VUS M P GN SSTXN SSTXP 6 GN 7 SSRXN 8 SSRXP 9 P_UP_TXM P_UP_TXP uF 0.uF US_VUS_UP see Page7 US_M_UP see Page7 US_P_UP see Page7 US_SSTXM_UP see Page7 US_SSTXP_UP see Page7 US_SSRXM_UP see Page7 US_SSRXP_UP see Page7 PV_OS 76 0uF J PV NI F 77 00MHZ 0.00uF SHIEL0 0 SHIEL US_TYPE_ONNETOR 7 uf GREEN 9 PV_ J7 NI PV R77 0 r uF 78.uF R78 0 r uF uF 8 0.0uF 8 0.uF F 00MHZ P_UP_TXM P_UP_TXP U7 + GN - TPEUS0_NI US_SSRXM_UP US_SSRXP_UP U8 + GN - TPEUS0_NI PV_ J8 NI F PV US_M_UP US_P_UP U9 + GN - 8 0uF uF uF 87 0.uF uF uF 90 0.uF 00MHZ TPEUS0_NI P0V_ Optional ES Protection J9 NI P0V F 9 uf uF 9 0.0uF 9 0.uF uF uF 97 0.uF uF uF 00 0.uF uF 0 0.0uF 0 0.uF 00MHZ P0V_ J0 NI F P0V 0 uf uF uF 07 0.uF 00MHZ PGE TITLE EXT POWER INTERFE TEXS INSTRUMENTS SIZE OUMENT NUMER 6696 REV PGE 8 of 8

25 IMPORTNT NOTIE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. ustomers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. ll products are sold subject to TI s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. ustomers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. uyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, uyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. uyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the uyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 699 requirements. uyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products pplications udio utomotive and Transportation mplifiers amplifier.ti.com ommunications and Telecom ata onverters dataconverter.ti.com omputers and Peripherals LP Products onsumer Electronics SP dsp.ti.com Energy and Lighting locks and Timers Industrial Interface interface.ti.com Medical Logic logic.ti.com Security Power Mgmt power.ti.com Space, vionics and efense Microcontrollers microcontroller.ti.com Video and Imaging RFI OMP Mobile Processors Wireless onnectivity TI EE ommunity Home Page ee.ti.com Mailing ddress: Texas Instruments, Post Office ox 60, allas, Texas 76 opyright 0, Texas Instruments Incorporated