for: Pool Heaters & Spas for: Gas Grills for: Patio Hearths & Lighting for: Emergency Generators Meter Risers, Fittings & PE Pipe for Underground Gas Applications Online Training & Certification at wal-rich.com CALL (0) CALL 221-1157 (0) 221-1157 www.wal-rich.com FAX (516) FAX 277-2177 (516) 277-2177 1
Continental Risers and Fittings for Underground PE Gas have been sold in the gas, plumbing, and propane markets since 19. Con-Stab fittings are IAPMO, CSA, & ICC approved. What is Continental s ID-Seal? What is Anodeless? From NFPA 54 Section 3.3.5 An anodeless riser is an assembly of steel-cased plastic pipe used to make the transition between plastic piping underground and metal piping aboveground. (O-RING) Con-Stab s patented ID-Seal is formed on the INSIDE of the pipe--where the surface is the smoothest. Therefore you must chamfer the INSIDE of your pipe with a Continental Chamfer tool. Plastic Pipe runs inside the riser. Corrosion-resistant fusion-bonded epoxy coating! CON-STAB ANODELESS METER RISERS (WITH FITTING) - Fusion-bonded epoxy coating - Anodeless and corrosion resistant - Patented ID-Seal fitting (inside chamfer) 28836 1/2 CTS.0 28804 3/4 IPS SDR-11 28808 1 IPS SDR-11 288 1 CTS.099/.101 28812 1 1/4 IPS SDR-10 28813 1 1/4 IPS SDR-11 28816 1 1/2 IPS SDR-11 28820 2 IPS SDR-11 You must use a Continental Chamfer Tool on a Continental Fitting! POLY-END ANODELESS METER RISERS - Fusion-bonded epoxy coating - Anodeless and corrosion resistant - Plain PE end can be used with compression & stab fittings Sleeved Elbow Unit 288 2 288 3 28802 3/4 IPS SDR-11 28806 1 IPS SDR-11 288 1 CTS.099/.101 28810 1 1/4 IPS SDR-10 28811 1 1/4 IPS SDR-11 28814 1 1/2 IPS SDR-11 28818 2 IPS SDR-11 288 2 IPS SDR-11 288 3 IPS SDR-11.5 2
LOOK FOR THE C You must use a Continental Chamfer Tool on a Continental Fitting! Con-Stab Chamfer Tools 28820 1/2 CTS.0 28814 3/4 IPS SDR-11 28816 1 IPS SDR-11 28822 1 CTS.099/.101 28806 1 1/4 IPS SDR-10 28807 1 1/4 IPS SDR-11 28808 1 1/2 IPS SDR-11 28810 2 IPS SDR-11 Con-Stab Couplings 2880 1/2 CTS.0 2882 3/4 IPS SDR-11 2884 1 IPS SDR-11 2881020 1 CTS.099/.101 2886 1 1/4 IPS SDR-10 2887 1 1/4 IPS SDR-11 2888 1 1/2 IPS SDR-11 2881010 2 IPS SDR-11 Con-Stab Elbows 28 1/2 CTS.0 2882 3/4 IPS SDR-11 2884 1 IPS SDR-11 2882020 1 CTS.099/.101 2886 1 1/4 IPS SDR-10 2887 1 1/4 IPS SDR-11 2888 1 1/2 IPS SDR-11 2882010 2 IPS SDR-11 Con-Stab Tees 2880 1/2 CTS.0 2882 3/4 IPS SDR-11 2884 1 IPS SDR-11 28820 1 CTS.099/.101 2886 1 1/4 IPS SDR-10 2887 1 1/4 IPS SDR-11 2888 1 1/2 IPS SDR-11 28810 2 IPS SDR-11 Poly-End x MIP Adapters 288 3/4 IPS SDR-11 28852 1 IPS SDR-11 288 1 CTS.099/.101 28854 1 1/4 IPS SDR-10 28855 1 1/4 IPS SDR-11 28856 1 1/2 IPS SDR-11 28858 2 IPS SDR-11 Con-Stab x Copper Flare 28802 3/4 IPS X 1/2 CTS Flare - To adapt PE to copper tubing. 4 18 Total Con-Stab x MIP Adapters 280 1/2 CTS.0 282 3/4 IPS SDR-11 284 1 IPS SDR-11 28820 1 CTS.099/.101 286 1 1/4 IPS SDR-10 287 1 1/4 IPS SDR-11 288 1 1/2 IPS SDR-11 28810 2 IPS SDR-11 Con-Stab End Caps 2892 3/4 IPS SDR-11 2894 1 IPS SDR-11 2896 1 1/4 IPS SDR-10 2897 1 1/4 IPS SDR-11 2898 1 1/2 IPS SDR-11 2892010 2 IPS SDR-11 Dresser Style 711 Bolted Couplings for PE W-R Description SDR 286 3 IPS 11.5 288 4 IPS 11.5 - Furnished with insert for use with polyethylene gas pipe - Grip rings create positive restraint 3
Con-Stab Reducers W-R IPS X IPS REDUCERS W-R RUN BRANCH SDR 28910 1 SDR11 x 3/4 SDR11 2891049 1 1/4 SDR10 x 3/4 SDR11 2891021 1 1/4 SDR10 x 1 SDR11 28910 1 1/4 SDR11 x 3/4 SDR11 2891022 1 1/4 SDR11 x 1 SDR11 2891010 1 1/2 SDR11 x 3/4 SDR11 2891012 1 1/2 SDR11 x 1 SDR11 2891013 1 1/2 SDR11 x 1 1/4 SDR10 2891014 1 1/2 SDR11 x 1 1/4 SDR11 2892 2 SDR11 x 3/4 SDR11 2894 2 SDR11 x 1 SDR11 2895 2 SDR11 x 1 1/4 SDR10 2896 2 SDR11 x 1 1/4 SDR11 2898 2 SDR11 x 1 1/2 SDR11 Con-Stab Reducing Tees 288 1 SDR11 x 3/4 SDR11 28861 1 1/4 SDR10 x 3/4 SDR11 28863 1 1/4 SDR10 x 1 SDR11 28862 1 1/4 SDR11 x 3/4 SDR11 28864 1 1/4 SDR11 x 1 SDR11 288 1 1/2 SDR11 x 3/4 SDR11 28882 1 1/2 SDR11 x 1 SDR11 28883 1 1/2 SDR11 x 1 1/4 SDR10 28884 1 1/2 SDR11 x 1 1/4 SDR11 288 2 SDR11 x 3/4 SDR11 28852 2 SDR11 x 1 SDR11 28853 2 SDR11 x 1 1/4 SDR10 28854 2 SDR11 x 1 1/4 SDR11 28856 2 SDR11 x 1 1/2 SDR11 Con-Stab Saddle Tees W-R MAIN OUTLET 289 1 1/4 3/4 SDR-11 28992 1 1/4 1 SDR-11 282 1 1/2 3/4 SDR-11 286 1 1/2 1 SDR-11 282 2 3/4 SDR-11 284 2 1 SDR-11 286 2 1 1/4 SDR-11 28942 3 3/4 SDR-11 28944 3 1 SDR-11 28946 3 1 1/4 SDR-11 28948 3 2 SDR-11 W-R CTS X IPS REDUCERS 280 1/2 CTS x 3/4 SDR11 28042 1/2 CTS x 1 SDR11 28002 1 CTS x 3/4 SDR11 28004 1 CTS x 1 SDR11 W-R THE SDR MIRACLE FITTING 28008 1 1/4 SDR-10 x SDR-11 Call us today for: - Free promotional materials - One-on-One sales training - Sizing/Technical assistance - Information about online training & certification CONFLEX FLEX RISERS A B Con-Flex risers are flexible casings that protect yellow PE pipe aboveground. Con-flex risers consist of CSST flex hose, with a durable UV & weatherresistant outer sleeve. Conforms to NFPA 54 & 58. May be used with Con-Stab couplings. W-R Description Length 28802 1/2 CTS.0 36 28804 1/2 CTS.0 84 288 1 CTS.099/.101 36 28820 3/4 IPS SDR-11 36 288 1 IPS SDR-11 36 288 1 1/4 IPS SDR-10 36 28842 1 1/4 IPS SDR-11 36 288 1 1/2 IPS SDR-11 36 288 2 SDR-11 36 Step 1. Step 3. 4 NEW SIZES! Instructions: 1. Disassemble the adapter coupling (B) 2. Feed the polyethylene pipe through the sleeve from the moisture seal (A) to the adapter coupling (B) 3. Assemble the adapter coupling by sliding the gasket over the tubing, and then pushing the tubing onto the insert. Tighten the compression nut until it bottoms out.
3/8 Quick-Connect Gas Appliance Hose 2862 120 Coated SS 2864 144 Coated SS - 3/8 Female Flare x 3/8 Male Quick-Connect - Gray UV resistant coating over S.S. stripwound tubing 3/4 Generator Hoses 28602 12 Coated SS 28606 24 Coated SS 28608 36 Coated SS 28603 12 Rubber 28607 24 Rubber 28609 36 Rubber - 3/4 Male (Swivel) x 3/4 Male (Swivel) Gas Outlet Boxes W-R Description Material W-R Description Material W-R Description 2862 White - 1/2 FIP Ang x 3/8 Fem Quick-Connect 28602 28604 2862 Straight 2864 Angle Quick-Connect Shutoff Valves 2862 Straight 3/8 FIP 3/8 F 2864 Angle 1/2 FIP 3/8 F 28606 Quick-Connect Fittings W-R Type Inlet Quick Connect W-R Type Inlet Quick Connect W-R# Description 28602 3/8 FIP 3/8 QC Female 28604 3/8 FIP 3/8 QC Male 28606 1/2 M Flare 3/8 QC Male 3 PE Elbows & Tees 28820 3 PE26 Elbow SDR-11.5 288 3 PE26 Tee SDR-11.5 Yellow Tracer Wire W-R Description 18420 0 14g 18422 0 18g - Use tracer wire in the trench along yellow polypipe for an effective, codecompliant installation. 3 x 0 Burial Tape W-R Description 242 Non-Detectable 24252 Magnetic (Detectable) - Burial Tape is used 6-8 above the pipe and tracer wire in the trench. 6-10 Adjustable Anodeless Riser Bracket W-R Description 286 3/4 to 2 Riser Bracket - Fits 3/4-1 1/2 anodeless risers - Adjustable from 6-10 from wall 5
PROPANE: LOW PRESSURE: 11 IN. W.C. Pressure Drop:.5 in w.c. Spec. Gravity: 1. Length 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS (feet) SDR-9.3 SDR-11 SDR-11 SDR-10 SDR-11 SDR-11 10 20 1 2 3 0 4 0 3 233 187 1 142 129 119 110 103 98 87 78 72 67 54 46 43 41 6 468 375 321 285 258 237 221 207 196 173 157 145 135 119 108 99 92 87 82 12 844 677 5 514 466 428 398 374 353 313 284 261 243 215 195 179 167 157 148 21 14 11 0 8 7 742 6 648 612 542 491 452 420 373 338 311 289 271 256 3210 2210 17 1520 13 1220 1120 10 978 924 819 742 683 635 563 510 469 436 9 387 57 39 31 27 2420 21 2010 18 17 16 14 13 12 11 1010 916 843 784 736 695 PROPANE: HIGH PRESSURE = 2PSI Pressure Drop: 1.0 in w.c. Spec. Gravity: 1. 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS Length (feet) 10 20 1 2 3 0 4 0 SDR-9.3 SDR-11 SDR-11 SDR-10 SDR-11 SDR-11 31 21 17 14 1310 11 10 1010 952 899 797 722 664 618 548 496 457 425 399 377 62 4 34 29 2620 23 21 20 1910 10 10 14 13 12 1 994 914 851 798 754 11 77 62 53 47 42 39 36 34 32 28 2610 20 22 19 17 16 15 14 13 1 1 92 81 7420 68 63 59 56 49 4520 41 38 34 3110 28 26 20 23 2 20 16 120 11 10 95 00 75 68 62 58 51 46 4320 20 37 35 53 3 29 25 22 20 1 17 16 15 1 12 11 9 84 77 7220 67 63 PROPANE PROPANE: FIRST-STAGE TO SECOND STAGE Pressure Drop: 1.0 in w.c. Spec. Gravity: 1. 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS Length (feet) 1 2 3 0 4 0 SDR-9.3 SDR-11 SDR-11 SDR-10 SDR-11 SDR-11 2143 1835 1626 1473 1355 1261 1183 1117 9 897 826 778 681 617 567 528 495 468 4292 3673 3256 29 2714 2525 2369 2238 1983 1797 1653 1539 1363 1235 1136 1057 992 937 7744 6628 5874 5322 4896 4555 4274 37 3578 3242 2983 2775 2459 2228 20 17 1789 16 13416 11482 10176 9220 8483 7891 74 6994 6199 5616 5167 47 42 38 3551 34 3 2928 202 173 15368 13924 12810 11918 11182 10562 9361 8482 73 7259 6434 58 5363 4989 4681 4422 362 31155 27612 219 217 21413 91 18978 16820 152 120 143 115 10474 9636 8965 8411 7945 PROPANE * Values listed are in cubic feet/meter (cfm). To calculate BTU, multiply by 0. ** Source: NFPA 54-2012 Table 6.2 (s) *Reproduced with permission from NFPA 54, National Fuel Gas Code, Copyright 2012. This reprinted material is not the complete and official position of the NFPA on the referenced subject, which is represented only by the standard in its entirety. Please consult your NFPA 54/ICC Fuel Gas codebook and appliance s technical literature for more detailed sizing and installation instructions. 6
YELLOW MEDIUM DENSITY (PE26) PE GAS PIPE NEW! FOOT CONVENIENCE COILS W-R# Size Wall (CTS) or SDR Length 28004 1/2 CTS.0 0 28011 3/4 IPS SDR-11 28012 3/4 IPS SDR-11 1 28016 3/4 IPS SDR-11 0 28020 1 CTS.099/.101 1 28021 1 CTS.099/.101 0 Conforms to ASTM D-2513 Gas 28025 1 IPS SDR-11 28022 1 IPS SDR-11 1 28026 1 IPS SDR-11 0 28029 1 1/4 IPS SDR-10 280 1 1/4 IPS SDR-10 1 For years, the gas utility market has used plastic gas pipe for its ease-of-use, corrosion resistance, and cost effectiveness. NFPA 54 provides for the use of plastic piping for outdoor, underground use only at a minimum burial depth of 18, using yellow 14g tracer wire for location purposes. Pressure Rating: Plastic Gas Pipe is rated to psi. 28031 1 1/4 IPS SDR-11 28032 1 1/4 IPS SDR-11 1 28036 1 1/4 IPS SDR-11 0 28041 1 1/2 IPS SDR-11 28042 1 1/2 IPS SDR-11 1 28046 1 1/2 IPS SDR-11 0 28051 2 IPS SDR-11 28052 2 IPS SDR-11 28056 2 IPS SDR-11 0 28062 3 IPS SDR-11.5 - Larger diameters available by special order NATURAL GAS: LOW PRESSURE < 2PSI Pressure Drop:.5 in w.c. Spec. Gravity:. 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS SDR-9.3 SDR-11 SDR-11 SDR-10 SDR-11 SDR-11 Length (feet) 10 20 1 2 3 0 4 0 201 138 111 95 84 76 65 61 58 51 46 43 35 32 29 27 26 24 3 277 222 1 169 153 1 131 123 116 103 93 86 71 64 59 55 51 48 726 499 1 343 4 276 254 236 221 209 185 168 154 144 127 115 106 99 93 88 12 865 695 594 527 477 439 9 383 362 321 291 268 249 221 184 171 1 152 10 1310 10 898 796 721 663 617 579 547 485 439 4 376 333 2 278 258 242 229 3410 23 18 1610 14 1 11 1110 10 983 871 789 726 675 598 542 499 464 435 411 NATURAL GAS: HIGH PRESSURE = 2PSI Pressure Drop: 1.0 in w.c. Spec. Gravity:. 1/2 IPS 3/4 IPS 1 IPS 1 1/4 IPS 1 1/2 IPS 2 IPS Length (feet) 10 20 1 2 3 0 4 0 SDR-9.3 SDR-11 SDR-11 SDR-10 SDR-11 SDR-11 18 12 10 878 778 5 649 3 566 535 474 429 395 368 326 295 272 253 237 224 3720 25 20 17 15 1410 1 1210 11 10 949 8 791 736 652 591 544 6 475 448 6710 4610 3710 31 2810 25 23 21 20 19 1710 15 14 13 11 10 981 913 856 9 110 79 6420 54 48 4410 37 35 33 29 26 24 2 20 18 10 15 14 10 1 12 96 8 73 66 61 50 53 44 37 34 27 25 23 22 2120 310 210 1 140 13 10 10 10 9610 72 6710 62 55 10 4610 42 20 NATURAL GAS 7
WAL-RICH CORPORATION UNDERGROUND GAS PRODUCTS 2017 Step 1: Pipe Step 2: Chamfer Inside of Pipe BE SURE TO MATCH PIPE SIZE & SDR* BEFORE SQUARE-CUT CHAMFER INSIDE AFTER CHAMFERRED Pipe, Fittings, and Chamfer Tool must be the same! * SDR stands for Standard Dimension Ratio. It is a designation of a pipe s pressure rating. SDR is the ratio of Pipe Diameter to Wall Thickness. Follow the arrows printed on the label. Only 3-5 turns necessary for a good chamfer! Test Gauge The coupon is the piece of yellow poly that is shaved off during the act of chamferring. Test your chamfer by pushing the pipe over the test gauge. If the pipe is chamferred properly, it should fit over the test gauge with minimum effort. Step 3: Mark Stab Depth Step 4: Stab & Check MARK THE STAB DEPTH! STAB PIPE INTO FITTING 1. 2. 1. Line up the end of the yellow pipe with the hub of the fitting. Stab the pipe completely into the fitting, so that the stab marker is within 1/8 from the entrance of the fitting. Hub 2. Mark a line on the pipe to approximate the end of the fitting. 3. Goal: The reason to mark the stab depth is to ensure that the pipe is sealed by both o-rings! 1/8 Once the pipe has been stabbed, it cannot be removed. (O-RING) LOOK FOR THE C You must use a Continental Chamfer Tool on a Continental Fitting! 8