Wall Mounted Cat Tree Instruction Manual Distributed by Designer Pet Products LLC - Westminster, CA 92683 Copyright C 2012 Designer Pet Products LLC - All rights reserved United States Patent Pending Made in China 08-2012
Thank You for purchasing a Wall Mounted Cat Tree. We hope that you will be very happy with your purchase. Please refer to the following instructions to set up your Wall Mounted Cat Tree. How to Care for your Wall Mounted Cat Tree You can clean the Cat Tree using a mild cleaner. Test cleaners in a discrete location first, such as an interior panel, to ensure that there is no adverse reaction. A handheld vacuum can be used on the carpet areas for cleaning. Do not expose Cat Tree to direct sunlight, drying heat sources, or dampness. Cat Tree has carpeted areas for your cat to relax. To attract your cat to Cat Tree, you could sprinkle some catnip on the carpet areas. Please watch cat to minimize aggressive behavior. The Cat Tree is designed to support cats up to 25 pounds safely. Setup size for each Cat Tree in the set: 32 (L) X 10 (W) X 14 (H). Warnings Before assembled, keep small parts away from children to avoid choking. The Cat Tree is designed to support cats up to 25 pounds safely. This is not a children s product. Keep children away from product. Do not sit on product as it is not designed as a bench to support the weight of a person. Do not climb or step on Cat Tree. Injury or death could occur. Do not hang on, rock, or shake Cat Tree. Injury or death could occur. Only someone experienced using a drill should use the drill for setup. Install the Cat Tree on a wall thicker than 1.5 thick.
Pieces Needed for Assembly Please follow all the instructions carefully. For assembly, you will need a Philip s head screw driver, a drill, a hammer, and a pencil. Please install on a carpet or rug to prevent scratches. Setup the Cat Tree with the entrance hole for the cat. Install the front wall with entrance hole (Part 1) with A screws. Install the back wall (Part3) with A screws. Note that the exterior wall of Part 3 has an inset edging. Attach the top of Cat Tree (Part 2) using A screws. Note that you can determine the top of Part 2 because the screws will drop into the screw holes. Also note that on the bottom of Part 2 you will see some additional holes for the brackets; install Part 2 with the bracket holes toward the carpet end & Part 1. Insert the Part C caps over the part A screws in Part 2.
Set up the Cat Tree without the entrance hole for the cat. Install the front wall without entrance hole (Part 3) with A screws. Install the back wall (Part3) with A screws. Note that the exterior wall of Part 3 has an inset edging. Attach the top of Cat Tree (Part 2) using A screws. Note that you can determine the top of Part 2 because the screws will drop into the screw holes. Also note that on the bottom of Part 2 you will see some additional holes for the brackets; install Part 2 with the bracket holes toward the carpet end & Part 3. Insert the Part C caps over the part A screws in Part 2. Now, please decide how you would like the Wall Mounted Cat Tree to be oriented and set up on your wall. The Wall Mounted Cat Tree set can be setup in a variety of ways. Think about what is best for you and your cat in your house. Note that each of the 2 parts in the set can be attached to the wall with the cat lounging area to the right or to the left (as shown above). Also, when deciding the orientation, please leave enough room for the cat to jump from one Cat Tree to the other. Now attach the brackets (Part D) to the 3 places on the Cat Tree with the entrance hole for the cat as shown using screws B.
Now attach the brackets (Part D) to the 3 places on the Cat Tree without the entrance hole for the cat as shown using screws B. Now that you have decided the orientation of the Wall Mounted Cat Tree, and have installed the brackets on the 2 parts in the set, it is time to affix the Cat Tree to the wall. Hold up the first Cat Tree against the wall. Mark the holes where the bracket is touching the wall with a pencil. Put Cat Tree on the ground. If you are mounting on drywall: With cat tree on the ground, carefully drill holes in the wall with a drill using a 13/64 size drill bit in the 6 spots you just marked with the pencil. Now, hammer the wall anchors part E into the 6 holes. Pick up the Cat Tree and install it to the wall using the F screws; screws the F screws into the wall anchors part E. Now attach the second Cat Tree to the wall by repeating the same steps in this Step 5. If you are mounting on solid wood or into a solid wood wall stud: Do not use the wall anchors- Part E. Instead pick up the Cat Tree and install directly into the wall using screws F. Ensure that the Cat Tree is securely attached to the wall before allowing your cat to climb on it. You have now set up your Cat Tree.