Smart bark control collar BC-2 User manual Important: Read this manual carefully before using the Smart Bark Control Collar for the safety of you and your dog.
Welcome to the Family! Thank you for choosing made4.pet! We at made4.pet are dog owners just like you and bark collars just like yours helps us train our beloved pets quickly and safely. We want your new collar to help you enjoy every minute you and your family have with your dog. To ensure you get the best experience we recommend carefully reading this instruction manual before training begins. Sincerely, made4.pet team 2
Table of Contents Introduction 4 Major features 4 Warning/Safety precautions 5 Package Content 6 Controls and settings 7 Getting Started 8 Installing the battery 8 Test #1 (ON/OFF) 8 Test #2 (functional) 8 Strap length and collar placement 9 Adjusting the sensitivity level 9 Before you start training 9 How do the training programs work 10 FAQ and troubleshooting 12 3
Introduction Smart Bark Control Collar stops your dog from barking by detecting its bark and delivering progressively increasing shock you control. There are 2 training programs: GREEN training program delivers progressively increasing beeping sounds and vibrations in 4 stages. It is recommended to start training with this program; it s enough for most dogs. RED training program delivers progressively increasing beeping sounds, vibration and electric shock in 6 stages. We strongly recommend only using the RED training program if the GREEN training program does not deliver the desired effect. Major features Super versatile for all dogs weighing at least 10 lbs Smart bark detection technology based on microprocessor 9 Levels of Sensitivity indicated on LCD display Protection mode for 90 seconds in RED training program Uses one 6-volt alkaline battery 4LR44 4
Warning/Safety precautions 1. The attached printed instruction manual is out of date, please use this PDF copy to operate the device properly. 2. Do not allow your dog to chew on this collar. You should also attempt to minimize scratching or clawing at the casing of the unit. 3. This device is made of plastic and electronic components that are not digestible. Consult your local vet if your dog swallows any part of this product. 4. The bark collar is not intended for use as a restraining collar. If you are using a leash, use it with a separate restraining collar. 5. Always use the soft silicone protective caps over the metal electrodes (prongs) to protect your dog s skin from pressure necrosis. 6. If the electrodes with silicone caps on directly touch the skin of your dog (it s necessary if you use RED training program) do not leave the collar on your dog for more than 10 hours. 7. It is very important to make sure the collar is adjusted properly on your dog s neck. Refer to Strap length and collar placement section. 8. LCD will automatically turn off after 10 seconds to save power. 9. LED will blink slowly when the system is running. 10. LED will blink quickly when the battery voltage is low. Please replace the battery. 11. If LCD indicates flashing L, the battery is low. Please replace the battery. 5
Package Content Check it right after you ve received the package! The printed paper instruction manual found in the package is out of date. Please use this PDF copy for updated instructions. 6
Controls and settings VOX+ button LCD indicates the current sensitivity level. LCD will automatically turn off after 10 seconds to save power. LCD will indicate flashing L if the battery is low. Please install a fresh one. SET/POW button LED indicates the current training program: Beep + Vibration Beep + Vibration + Shock mode LED will blink once every 2 seconds in working mode. LED will blink twice every second when the battery voltage is low. Please replace the battery. Put electrodes and the appropriately sized silicone protective caps on the prongs before you start using the device VOX+ This button allows you to cycle through the sensitivity levels from 1 to 9. The higher the number, the higher the sensitivity. SET/POW Multiple function button: Power on/off button -- Press and hold this button for 2 seconds to power on this device. The device will vibrate once it is turned on. -- Press and hold this button for 2 seconds to power off the device with a tone Training Programs switch button -- Press this button to switch between training programs: GREEN program LED blinks in GREEN. Beep + Vibration We suggest using this training program in the beginning. If your dog does not respond and continues barking, you may switch to RED. RED program LED blinks in RED Beep + Vibration + Shock mode 7
Getting Started Installing and removing the battery (type Alkaline 4LR44 6V) 1. Open the battery door located on the front side of the unit. 2. Place the negative end of the battery against the coil (spring) in the device. Push the battery towards the coil to insert the battery then push the positive end downward to the clip to fully insert the battery. This is the only way to install the battery. Otherwise, you may damage to coil. 3. To remove the battery, use a flat head screwdriver or a knife and place it in the gap between the battery and the device on the positive end. Carefully pull the battery out. Do not start with negative end in order to avoid negative coil damage. 4. If LED blinks quickly (faster than twice per second) and/or LCD indicates flashing L, please replace the battery with a fresh one. Test #1 (ON/OFF) (make sure the device is OFF before the test) 1. Turn on the device by long pressing the right SET/POW button. It will vibrate and show blue digits on the LCD screen indicating the sensitivity level. 2. Long press the right button SET/POW to switch the device off. It will beep before powering down. Perform this test to ensure the beeper and vibrator work correctly. If the test fails at any step please refer to the Troubleshooting Guide at the end of this manual. Test #2 (functional) (must be performed each time you are going to use it) 1. Turn on the device (refer to Controls and Settings section for details) 2. If you want to use GREEN training program: a. Switch to GREEN training program (refer to Controls and Settings section for details). b. Switch the sensitivity level to 9 (refer to Controls and Settings section for details). c. Imitate barking by shouting HOW or WOW right into the bark detector hole. Do it loudly and do not hesitate. Repeat several times in case the collar does not go off the first time. d. The collar goes off by beeping and vibrating the first time it detects barking. 3. If you want to use RED training program: a. Switch to RED training program (refer to Controls and Settings section for details) b. Switch the sensitivity level to 9 (refer to Controls and Settings section for details) 8
c. Imitate barking by shouting HOW or WOW right into the bark detector hole. Do it loudly and do not hesitate. Repeat several times in case the collar does not go off the first time. d. The collar goes off by beeping and vibrating the first time it detects barking. e. Repeat Step c within 30 seconds after the collar goes off and immediately place the plastic tester over the metal prongs. Ensure the wires inside the tester are in consistent contact with the prongs of the collar. f. The collar goes off by beeping, vibrating and distributing electric shock. During the shock stage, the LED inside the tester will glow for one second. If the test fails at any step please refer to the Troubleshooting Guide at the end of this manual. Strap length and collar placement Your bark collar comes pre-assembled making it easy to get started. Adjust the length of the woven strap to your dog by placing it in a comfortable place on your dog s neck. Make sure the device is OFF before putting the collar on your dog. The collar must fit snugly enough so that it does not move around on your dog s neck. The electronic unit must be placed right on the windpipe (vocal cord). Do not shift it to either side of the neck. The prongs with metal electrodes and silicone caps on should have consistent contact with your dog s skin if you use the RED training program. Thin or shave the hair in the contact area if necessary. Remember: Proper strap length and placement will provide the best results for your bark collar. Adjusting the sensitivity level The default sensitivity level is 5. Adjust the sensitivity based on the needs of your dog. If you notice the collar goes off too often even when the dog does not bark, lower the sensitivity for better results (refer to Controls and Settings section for details). Conversely, if the device does not go off when your dog does bark adjust the sensitivity gradually to a higher level. Before you start training Getting Started 1. Make sure you ve put the protective silicone caps on the metal electrodes. 2. Choose your training program. We recommend starting with the GREEN training program. If you do not achieve the desired results, you can always switch to the RED training program. 3. Make sure you ve performed all of the testing procedures. 4. Make sure you ve adjusted the strap length and put the collar on your dog s neck properly. 5. Start using the device by turning it ON and adjusting the sensitivity level if necessary. 9
How do the training programs work General notes The collar starts the training program each time it detects barking. Each training program consists of sequential stages, meaning a new stage starts immediately after the previous one has completed. A new stage will begin after the previous one if your dog continues barking. If your dog does not continue to bark, the program will not advance to the next stage. During each stage, the collar may deliver a beep sound, vibration, and a shock pulse according to the chosen program and stage number. If the dog does not bark for more than a 30 second period, the program resets to the first stage and will remain idle until the dog starts barking again. GREEN training program consists of 4 stages: # 1: Beeps for 5 seconds then vibrates for 3 seconds # 2: Beeps for 4 seconds then vibrates for 5 seconds # 3: Beeps for 3 seconds then vibrates for 8 seconds # 4: Beeps for 3 seconds and vibrates for 10 seconds at the same time 10
How do the training programs work RED training program consists of 6 stages: # 1: Beeps for 3 seconds then vibrates for 5 seconds. No Shock # 2: Beeps for 3 seconds, vibrates for 3 seconds and then delivers shock for 1.5 seconds (weak shock) # 3: Beeps for 3 seconds, vibrates for 3 seconds and then delivers shock for 1.5 seconds (stronger shock) # 4: Beeps for 3 seconds, vibrates for 3 seconds and then delivers shock for 1.5 seconds (stronger shock) # 5: Beeps for 3 seconds then shocks for 1.5 seconds (high shock) # 6: Beeps for 3 seconds then shocks for 1.5 seconds (highest shock) Protection mode: After step #6, the system will go into protection mode for 90 seconds to protect your dog from getting hurt. In protection mode, the red LED will glow for the full 90 seconds. 11
FAQ and troubleshooting Is there a battery indicator? Yes, if the LED (either red or green according to the chosen training program) blinks faster than usual (appx. twice per second to indicate low battery) please replace the battery. If Test #1 Fails Make sure the battery is inserted properly: the negative end of the battery to the end of the coil (spring), the positive end of the battery to the end of the clip. Install a new battery. If the device was exposed to water, remove the battery as soon as possible. Completely submerge the electronic unit in pure alcohol for 1 hour and let the unit air dry for 24 hours. Repeat the first two steps if necessary. If the problem persists, contact our support team and describe which exact step of the test you re having trouble with. If possible, provide close, detailed pictures of the battery slot and the unit. This may help resolve the issue faster so you can get back to training ASAP! If Test #2 Fails Make sure you ve successfully performed Test #1 Make sure the sensitivity level is set to 9 Perform the shouting test louder Bring your face as close as possible to the bark detector hole so your lips slightly touch the unit and try the shouting test again. If the problem persists, contact our support team and describe which exact step of the test you re having trouble with. If possible, provide a short video showing the problem. This may help resolve the issue faster so you can get back to training ASAP! My package is missing some parts. No batteries/electrodes/silicone caps etc. Unfortunately, there are times where Amazon may reintroduce a returned collar that may be missing parts to new inventory where they may mistakenly ship it out again. In the unlikely event one of our collars is returned, Amazon does not allow made4.pet to run a quality check which may result in missing parts. For this reason, we ask you to check the package content in the very beginning and make sure everything is there. If you a recipient of one of these packages contact us as soon as possible. I need a new battery but don t know which to buy. The battery type used by the collar is 4LR44 6V Alkaline. This battery also goes by other common names like PX28A, A544, K28A, and V34PX. How long does one battery last? Battery life depends on how frequently your dog barks. The bark collar can last up to a few weeks or more if your dog is not a frequent barker. The collar also comes with two batteries in the package that will last a long time for dogs that bark infrequently. If you find that your battery may be partially depleted or defective, contact our support team. 12
FAQ and troubleshooting Is the collar waterproof? While the bark collar is not waterproof, it is rainproof and light rain should not cause any problems. We strongly recommend avoiding excessive water exposure in order to preserve the proper functionality of the unit. If water exposure occurs take out the battery as soon as possible, completely submerge the electronic unit in pure alcohol for 1 hour and let the collar air dry for 24 hours. My dog does not respond to the collar. Make sure the collar goes off when your dog barks. If your dog has thick hair use longer prongs and the appropriate silicone conductive caps for the prongs. Thin or shave long hair in the contact spot if necessary to achieve better results. Use the RED training program if necessary and make sure there is a consistent contact between electrodes and dog s skin. Older dogs might have poorer hearing and may not react to the beeps. Older dogs may be so set in their habits that the collar s correction alone may not be enough. In cases like these, you may need to assist with the training to achieve desired results. The collar does not go off when my dog barks Make sure you ve successfully performed Test #2 before putting the collar on your dog. Make sure the collar is ON (LED must blink once every 2 seconds). Make sure you ve made the right adjustments and placement for the collar. Refer to Strap length and collar placement section for help and instructions. Switch to higher sensitivity level. The collar goes off even if my dog doesn t bark Make sure you ve made the right adjustments and placement for the collar. Refer to the Strap length and collar placement section section for help and instructions.if the collar moves around the neck it may trigger the device. Switch to lower sensitivity level. If you ve followed all of the instructions and performed all of the recommendations and still run into issues please do not hesitate to contact our support team at support@made4.pet. Provide as much information as possible (including photo and video) so we can help you as soon as possible! 13
Activate your free guarantee at www.made4.pet We d really appreciate it if you could find few minutes to share your share your 5-star experience with the bark collar! Help other savvy Amazon users make the best choice for a bark collar. If for any reason you re not satisfied let us know so we can make it right! We want to do our best to meet your expectations now that you re part of the made4.pet family. Send us an e-mail at support@made4.pet if you have any questions or concerns about your made4.pet purchase.